Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 22 (Cont'd)

—_— ~ CONNECT

INSPECTION START

]| 34 ¢€ >

(_c/unir_[e] CONNECTOR

38°47 Vv Se | O.K.

CHECK GROUND CIR-

CHECK POWER SUPPLY.

Vv 1) Turn ignition switch ‘ON’. CUIT. 2) Check voltage between E.C.U. termi- 1) Turn ignition switch WwW © nals 68, @ and ground. “OFF”. 2) Disconnect E.C.U. har- Voltage: Battery voltage YW? m ness connector. N.G. 3) Check harness continu- SEF 182K ity between E.C.U. ter- minals ©, @),GoD, BI DISCONNECT

G0 G1 and engine

€:}

_c/unit “fol CONNECTOR |

ground. 613-107-108 +116 Continuity should exist. N } a a lf N.G., repair harness or connectors. yo ro Check E.C.U. pin termi- (i nals for damage or the connection of E.C.U. har- = SEF183K ness connector. DISCONNECT DISCONNECT aA €) ‘ Ee) N.G. Check the following.

CHECK HARNESS CONTINUITY

Vv

([_c7unit fol CONNECTOR ]

e Harness connectors

BETWEEN E.C.C.S. RELAY AND E.C.U.

1) Turn ignition switch ‘OFF’. 38°47 e Harness continuity 2) Disconnect E.C.U. harness connec- between E.C.U. and tor. E.C.C.S. relay 3) Disconnect E.C.C.S. relay. lf N.G., repair harness or 4) Check harness continuity between (& E.C.U. terminals , @ and termi- connectors. nal @ . MEF679A Continuity should exist. DISCONNECT [p)

aah id €&)

ID] \ O.K. 5 Nea) N.G. Check the following.

CHECK VOLTAGE BETWEEN E.C.C.S.

e “BR” fusible link 1) Check voltage between terminals @ e Harness continuity between E.C.C.S. relay , &) and ground. iV, CO and battery Voltage: Battery voltage ~ wr 4 If N.G., repair harness or (F O.K. connectors. t N.G MEF680A

RELAY AND GROUND.

Check the following. e Harness connectors (#2),

CHECK VOLTAGE BETWEEN E.C.U.

AND GROUND.

— DISCONNECT 1) Check voltage between E.C.U. termi- [cum [

C/UNIT eI CONNECTOR | 4 €:)

[ot connector J

e.8 nal and ground. e “BR” fusible link e Harness continuity Voltage: Battery voltage between E.C.U. and O.K. battery If N.G., repair harness or W YY connectors. (& y ® SEF185K

EF & EC-94

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.