Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

REAR DISC BRAKE (CL9H) - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › REAR DISC BRAKE (CL9H) - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXREAR DISC BRAKE (CL9H) - Nissan 240SX 1991-1992 Workshop Manual

REAR DISC BRAKE (CL9H)

REAR DISC BRAKE (CL9H)

Copper washer 629 #9 17 -20(1.7 - 2.0, 12 - 14) Air bleeder Brake hose © (C) 7 -9 (0.7 -0.9, 5.1 -6.5) e=.—__——*—_ Pin bolt (O) 22 - 31 (2.2 -3.2, 3 16 - 23) We Cam ® ey Cam bolt eo 4 “~

Cylinder body

Return spring \ ’ (0) Lever . \GL~ | : N-m (kg-m, ft-lb) @ a washer | 0) 92 -31(2.2-32,

O\ Gg A 25 - 29 (2.5 - 3.0, yy) 16 - 23) grease or silicon-based Ya 18 - 22) Y < [- | grease point 7X ES (®) : Rubber grease point

® : P.B.C. (Poly Buty! Cuprysil)

® : Brake fluid point

BA Rod Ea)

Torque member

‘> Cable stay 7 : i i - fixing bolt a-O 26 - 36 (2.7 -3.7, 20 - 27) EA® Oring Z mush i ee ® ~ (0) 38 - 52 (3.9 -5.3, 28 - 38)

Inner shim

. . ®)

Lo RY Piston seal (59 BEd

rod 3 Xe Ring C ° —— Spacer Spring

Key plate

Pad retainer an

wave washer

en Spring cover

2) . ° Pin Beg SOS ; Spacer xO a B 4 S Adjusting nut Outer pad Cur (9 Ea ®) Outer shim \. Piston ~

Torque member

Pad

Tm retainer ®) %<) ER) SBR481A

Piston boot

Pad Replacement

CAUTION: When cylinder body is swung up, do not depress brake pedal because piston will pop out. @ Release parking brake. @ Remove parking cable stay fixing bolt, pin bolts and lock spring. Then remove pad retainers, pads and shims.

@ When installing pads, retract piston into cylinder body by turning it clockwise. Be careful not to damage piston boot or get oil on rotor. Always replace shims when replacing pads.

SBR641 |" BR-16

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.