Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 33 (Cont'd)

Ps DISCONNECT

cafete y” €)

INSPECTION START

= 6e)

Vv

CHECK POWER SUPPLY.

N.G. ,| Repair harness or con- | Kt) Oy 1) Disconnect throttle sensor harness nectors. connector. (Ei) 2) Turn ignition switch ‘‘ON”’. 3) Check voltage between terminal © * and ground. MEFTO1A Voltage: Approximately 5V O.K. DISCONNECT : Bi 9)4 No €) a :

CHECK GROUND CIRCUIT.

N.G. ,| Repair harness or con- yr 1) Turn ignition switch “‘OFF’’. nectors. [Q] 2) Check harness continuity between Le terminal @ and engine ground. Continuity should exist.

¥ 1 MEF702a|

| CHECK INPUT SIGNAL CIRCUIT.

N.G. ,| Repair harness or con- | a ca 1) Reconnect throttle sensor har- nectors. ness connector.

M@ THROTTLE SENSOR CKT

2) Turn ignition switch ‘““ON’’. DEPRESS 3) Perform

THROTTLE SENSOR

CKT” in ‘FUNCTION TEST” ee eN

mode with CONSULT.

TOUCH START

OR S\ 3) Read throttle sensor output voltage in ‘‘WORK SUPPORT” mode with CONSULT. | next | START | Throttle valve fully closed: SEF634L Approx. 0.5V Throttle vaive fully open: Approx. 4.0V

THROTTLE SEN ADJ BL]

OR

# & & &ADJ MONITOR ##%%

1) Disconnect E.C.U. harness connector.

THROTTLE SEN

0.44V 2) Check harness continuity

====== MONITOR =======

between E.C.U. terminal 0)

CAS-RPM (REF)

687rpm and terminal ©.

IDLE POSITION

ON

Continuity should exist.

O.K. v SEF725K

CHECK COMPONENT

N.G. ,| Replace throttle sensor. ry ea a Uscomnect (Throttle sensor). ~ DISCONNECT €) €)

Refer to “Electrical Components

— Inspection’. — (L_c7unr

[ol CONNECTOR J|

Glble)

(See page EF & EC-166.)

” O.K. Vv Check E.C.U. pin terminals for damage (ta } or the connection of E.C.U. harness con- iF} ; D, nector. MEF800A EF & EC-125

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.