Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 29 (Cont'd)

California model

INSPECTION START

O.K.

CHECK VACUUM SOURCE TO

CHECK COMPONENTS

Vv

E.G.R. CONTROL VALVE.

(E.G.R. control valve, B.P.T. 1) Start engine and warm it up valve and exhaust gas tempera- Vacuum hose connected sufficiently. ture sensor). to E.G.R. control valve 2) Perform self-diagnosis. Refer to ‘‘Electrical Components MEF694A Make sure that none of the Inspection’. - codes No. 12, No. 13, No. 35 (See page EF & EC-185, 186.)

|[__ cart [ol connecTor ||

or No. 43 are displayed. N.G. 3) Keep engine speed at about L 2,000 rpm. 4) Disconnect vacuum hose to E.G.R. control valve. ) © 5) Make sure that vacuum exists under the following condi- tions. Vv Replace malfunctioning compo- At idle: MEF695A Vacuum should not exist. nent(s). Engine speed is about 2,000 = ; rpm.: Vacuum should exist. Split v N.G. 3) O.K.

CHECK CONTROL FUNCTION.

| CHECK VACUUM HOSE.

- 1) Check vacuum hose for clog-

1) Check voltage between E.C.U. Clogging terminald@o>and ground under ging, cracks and proper con- the following conditions. nection. —=

AN Improper connection

Voltage: At idle SEF816F Approximately 0V Engine speed is about 2,000 rpm. Battery voltage N.G. | y N.G.

CHECK POWER SUPPLY.

Check the following. e Harness connectors(), 1) Stop engine. 2) Disconnect E.G.R. & canister e 10A fuse control solenoid valve har- e Harness continuity between ness connector. E.G.R. & canister control sole- 3) Turn ignition switch ‘“‘ON’’. noid valve and fuse MEF696A 4) Check voltage between termi- If N.G., repair harness or con- nal @) and ground. nectors. €) ad € Voltage: Battery voltage 5 O.K.

|_cAntT el comecror ||

105

® MEF697A

EF & EC-121

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.