Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 4 (Cont’d)

i t38) TS. relay A/C 43 connector (E42) DISCONNECT €) Check circuit continuity be- tween A/C relay harness termi- nal No. @3) and E.C.CS. control \G&

unit harness terminal No. @).

E.C.C.S. control unit connector (2) 24 |

- Note Vv N.G.

CAINIT [0] CONNECTOR |

CHECK VOLTAGE FOR

SHA029D Check circuit continuity be-

THERMO CONTROL AMP.

tween E.C.C:S. control unit Thermo control amp. Do more than 8 volts exist be- harness terminal No. @1) and connector (#9) tween thermo control amp. thermo control amp. harness ter- ih a € harness terminal No. and

minal No. @.

4] a €> body ground? L/G O.K. O.K. X y Vv 5 ry .

CHECK E.C.C.S. CONTROL

CHECK POWER SUPPLY

UNIT.

FOR THERMO CONTROL

Refer to EF & EC section. AMP. — AIC Go to Main Power Supply and = SHAO30D Ground Circuit Check. Thermo control amp. connector N.G. Disconnect push control unit

CHECK BODY GROUND

_ harness connector.

CIRCUIT FOR THERMO

CONTROL AMP.

ae ol Note Disconnect thermo control amp. oo harness connector. Check circuit continuity be- Does continuity exist between tween thermo control amp. a» 234 3 OFF harness terminal No. (3 thermo control amp. harness AIC =

terminal No. (3) and body

and push control unit harness SHA031D

terminal No. (3).

ground? = Thermo control O.K. O.K. > f amp. connector Vv e 1 Replace thermo control amp. we+ (& +— E C.C.E. contro! unit connector ah

|[__ eat 7 fol CONNECTOR

|| SHA032D | | Thermo control Ga amp. connector HS

LG/B f @ Sn ere © LG/B | (Go to next page.) {e) 13 Note: Push control unit

If the result is N.G. after checking circuit continuity, repair harness or

connector SHA033D connector.

HA-86

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.