Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

How to Perform Trouble Diagnoses for Quick and Accurate Repair (Cont'd)

INTERMITTENT PROBLEM SIMULATION

In order to duplicate an intermittent problem, it is effective to create similar conditions for component parts, under which the problem might occur. Perform the activity listed under THIS is the Service procedure and note the result. symptom, < isn't it ? J

SEF235G

Variable factorInfluential partTarget conditionService procedure hose and apply vacuum.
tioPressure regulatorMade leanRemove vacuum hose and apply vacuum.
1 | Mixture ratioPressure regulatorMade lean Made richRem Remove vacuum hose and apply pressure. ockwise.
oe 2 | Ignition timingCrank angle sensorAdvancedRotate distributor clockwise.
oe 2 | Ignition timingCrank angle sensorAdvanced RetardedRotate distributor counterclockwise.
3 Mixture ratio feedbackExhaust gas sensorSuspendedDisconnect exhaust gas sensor harness con- 9 nector. Perform self-diagnosis (Mode II) at 2,000 9 | )
3 Mixture ratio feedback controlControl unitOperation checkPerform self-diagnosis (Mode II) at 2,000 9 | ) rpm. .
speedA.A.C. valveRaisedTurn idle adjusting screw counterclockwise.
4 | Idle speedA.A.C. valveRaised LoweredTurn idle adjusting screw clockwise.
Electrical connectionHarness connectorsPoor electrical con-Tap or wiggle. i i i
Electrical connection 5 Ines (Electric continuity)Harness connectors and wiresPoor electrical con- nection or improper wiringi i i Race engine rapidly. See if the torque reac- tion of the engine unit causes electric breaks.
breaks.
CooledCool with an icing spray or similar device.
6 | TemperatureControl unitWarmedHeat with a hair drier. . [WARNING: Do not overheat the unit.]
Wet. pour water on
7 | MoistureElectric partsDamp[WARNING: Do not directly pour water on components. Use a mist sprayer.]
7 | Mosprayer.]
8 | Electric loadsLoad switchesLoadedTurn on headlamps, air conditioner, rear de- P fogger, etc. e sensor body.
9 | Idle switch condition _ 10 | Ignition spark gn parControl unit imi i Timing lightON-OFF switching check Spark powerRotate throttle sensor body. Try to flash timing light for each cylinder us- ing ignition coil adapter (S.S.T.).

EF & EC-38

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.