TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
- Make
- Nissan and Datsun
- Model
- 240SX Nissan 240SX 1991-92 Workshop Manual
- Section
- General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
‹ Prev TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop ManualNext › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
TROUBLE DIAGNOSES
TROUBLE DIAGNOSES
How to Perform Trouble Diagnoses for Quick and Accurate Repair (Cont'd)
INTERMITTENT PROBLEM SIMULATION
In order to duplicate an intermittent problem, it is effective to create similar conditions for component parts, under which the problem might occur. Perform the activity listed under THIS is the Service procedure and note the result. symptom, < isn’t it ? J
SEF235G
| Variable factor | influential part | Target condition | Service procedure |
|---|---|---|---|
| Mixture ratio | Pressure regulator | Made lean | Remove vacuum hose and apply vacuum. |
| 1 | Mixture ratio | Pressure regulator | Made lean Made rich | Remove vacuum hose and apply pressure. |
| g | Crank angle sensor | Advanced | Rotate distributor clockwise. |
| 2 | Ignition timing | Crank angle sensor | Advanced Retarded | Rotate distributor counterclockwise. |
| 3 Mixture ratio feedback | Exhaust gas sensor | Suspended | Disconnect exhaust gas sensor harness con- 9 nector. Perform self-diagnosis (Mode II) at 2,000 ( ) |
| 3 Mixture ratio feedback control | Control unit | Operation check | Perform self-diagnosis (Mode II) at 2,000 ag ( ) rpm. |
| 4 | Idle speed | A.A.C. valve | Raised | Turn idle adjusting screw counterclockwise. |
| 4 | Idle speed | A.A.C. valve | Lowered | Turn idle adjusting screw clockwise. |
| Electrical connection | Harness connectors | Poor electrical con- | Tap or wiggle. i i i |
| Electrical connection 5 nes | Harness connectors | Poor electrical con- nection or improper wiring | i i i Race engine rapidly. See if the torque reac- tion of the engine unit causes electric |
| Electrical connection 5 nes (Electric continuity) | and wires | wiring | tion of the engine unit causes electric |
| breaks. | |||
| Cooled | Cool with an icing spray or similar device. | ||
| 6 | Temperature | Control unit | Warmed | Heat with a hair drier. . |
| 6 | Temp | Warmed | . [WARNING: Do not overheat the unit.] | |
| Wet. | |||
| 7 | Moisture | Electric parts | Damp | [WARNING: Do not directly pour water on components. Use a mist sprayer.] |
| sprayer.] | |||
| 8 | Electric loads | Load switches | Loaded | Turn on headlamps, air conditioner, rear de- ' P fogger, etc. |
| 9 | Idle switch condition wg: 10 | Ignition spark | Control unit oo . Timing light | ON-OFF switching | Spark power check | Rotate throttle sensor body. Try to flash timing light for each cylinder us- y ing "9 y ing ignition coil adapter (S.S.T.). |
EF & EC-38
‹ Prev TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop ManualNext › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
Parts & tools for this job For Nissan 240SX
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLSocket setSearch: socket set metric
- BOOKHaynes manualSearch: Haynes manual Nissan 240SX
As an Amazon Associate we earn from qualifying purchases.