Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

GENERAL MAINTENANCE - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › GENERAL MAINTENANCE - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXGENERAL MAINTENANCE - Nissan 240SX 1991-1992 Workshop Manual

GENERAL MAINTENANCE

GENERAL MAINTENANCE

General maintenance includes those items which should be checked during the normal day-to-day operation of the vehicle. They are essential if the vehicle is to continue operating properly. The owners can perform the checks and inspections themselves or they can have their NISSAN dealers do them for a nominal charge.

ItemReference page
OUTSIDE THE VEHICLE
The maintenance items listed here should be performed from time to time, unless otherwise specified. |
Tires Check the pressure with a gauge periodically when at a service station, including the
spare, and adjust to the specified pressure if necessary. Check carefully for damage, cuts or wear._
excessive wear.
Wheel nuts When checking the tires, make sure no nuts are missing, and check for any loose
nuts. Tighten if necessary.
Tire rotation Tires should be rotated every 12,000 km (7,500 miles.)MA-19 -
Wheel alignment and balance If the vehicle should pull to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a needMA-18 FA-7
straight and level road, or if you detect uneven or abnormal tire wear, there may be a needFA-7
for wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel
balancing may be needed.
Windshield wiper blades Check for cracks or wear if they do not wipe properly._
Doors and engine hood Check that all doors and the engine hood operate smoothly as well as the trunk lid and back hatch. Also ensure, that all latches lock securely. Lubricate hinges,
the trunk lid and back hatch. Also ensure, that all latches lock securely. Lubricate hinges,
latches, rollers and links if necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released.MA-21
from opening when the primary latch is released.MA-21
When driving in areas using road salt or other corrosive materials, check lubrication frequent-
ly.
INSIDE THE VEHICLE
The maintenance items listed here should be checked on a regular basis, such as when
performing periodic maintenance, cleaning the vehicle, etc.
Lights Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim.
are all operating properly and installed securely. Also check headlight aim.
Warning lights and buzzers/chimes Make sure that all warning lights and buzzers/chimes are
operating properly.
Windshield wiper and washer Check that the wipers and washer operate properly and that
the wipers do not streak.
Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner.
Steering wheel Check that it has the specified free play. Be sure to check for changes in the steering condition, such as excessive free play, hard steering or strange noises. .—
steering condition, such as excessive free play, hard steering or strange noises. .—
_ Free play: Less than 35 mm (1.38 in)
Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and that all latches lock securely in every position. Check that the
they operate smoothly and that all latches lock securely in every position. Check that the head restraints move up and down smoothly and that the locks (if so equipped) hold secure-—
head restraints move up and down smoothly and that the locks (if so equipped) hold secure-—
ly in all latched positions. Check that the latches lock securely for folding-down rear seat-
backs.
Seat belts Check that all parts of the seat belt system (e.g. buckles, anchors, adjusters and
retractors) operate properly and smoothly, and are installed securely. Check the beltMA-21
webbing for cuts, fraying, wear or damage.

MA-2

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.