Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

DISCHARGING, EVACUATING, CHARGING AND CHECKING - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › DISCHARGING, EVACUATING, CHARGING AND CHECKING - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXDISCHARGING, EVACUATING, CHARGING AND CHECKING - Nissan 240SX 1991-1992 Workshop Manual

DISCHARGING, EVACUATING, CHARGING AND CHECKING

DISCHARGING, EVACUATING, CHARGING AND CHECKING

Charging Refrigerant (Cont'd)

6. Turn on heater switch (charging cylinder is provided with a heater.) The refrigerant charging time can be reduced by heating refrig- erant to increase its pressure. In this case, do not allow the

pressure in cylinder to rise higher than 1,030 kPa (10.5 kg/cm’,

150 psi). (If pressure rises above this level, turn off the heater.) The pressure in the charging cylinder can be measured by upper pressure gauge. CAUSE PRESSE Pie

RHA679B

SETTING OF FLOW METER

1. Rotate charging cylinder main body until scale for R12 is at the correct position on sight glass.

2. Read charging cylinder pressure gauge.

3. Rotate charging cylinder so that scale of charging cylinder agrees with pressure value indicated on pressure gauge.

RHA680B

CALCULATING CHARGING AMOUNT OF REFRIGERANT

1. Record the amount of refrigerant in the sight glass before charging.

2. Subtract the required amount of refrigerant (charge quan- tity specified for the vehicle) from the amount of refrigerant recorded in step 1. Charge refrigerant into the system until Sight the remaining value equals to the value indicated on the glass sight glass. {| Referigerant level before charging Example: —— = Level in sight glass: 3 Ib 8 oz Specified amount Charge specification (from Service Manual) 2.0 - 2.4 Ib. of charge Calculate charge quantity into Ib and oz as follows: 1 Ib = 16 SS oz, and 0.1 Ib = 1.6 oz, so that 2.0 Ib = 32 oz, 2.4 lb = 32 + Refrigerant level (4 x 16) = 32 + 6.4 = 38.4, round off to 38. Therefore our after charging charge quantity will be between 32 and 38 oz, or 2 Ib 0 oz to 2 Ib 6 oz. Subtract 2 Ib 6 oz from level in sight glass (3 Ib 8 oz) = 1 Ib 2 OZ. This will be our ending point.

RHA681B HA-30

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.