TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
- Make
- Nissan and Datsun
- Model
- 240SX Nissan 240SX 1991-92 Workshop Manual
- Section
- General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
TROUBLE DIAGNOSES
TROUBLE DIAGNOSES
Self-diagnosis — Mode II (Self-diagnosticresults) (Cont'd)
| Code No. | Detected items | Malfunction is detected when ... | Check item (remedy) |
|---|---|---|---|
| 11° | Crank angle sensor cir- | |@ Either 1° or 90° signal is not entered for the first | |@ Harness and connector (If |
| cuit | few seconds during engine cranking. | harness and connector are | |
| e Either 1° or 90° signal is not input often enough | normal, replace crank angle | ||
| while the engine speed is higher than the speci- | sensor.) | ||
| fied rpm. | |||
| 12 | Air flow meter circuit | e The air flow meter circuit is open or shorted. (An | |@ Harness and connector (If |
| abnormally high or low voltage is entered.) | harness and connector are | ||
| normal, replace air flow | |||
| meter.) | |||
| 13 | Engine temperature | e The engine temperature sensor circuit is open or | |e Harness and connector |
| sensor circuit | shorted. | e Engine temperature sensor | |
| (An abnormally high or low output voltage is | |||
| entered.) | |||
| 14 | Vehicle speed sensor | e The vehicle speed sensor circuit is open or | e@ Harness and connector |
| circuit | shorted. | e Vehicle speed sensor (reed | |
| switch) | |||
| 21* | Ignition signal circuit | e The ignition signal in the primary circuit is not | e Harness and connector |
| entered during engine cranking or running. | e@ Power transistor unit | ||
| 31 | E.C.U. | e E.C.U. calculation function is malfunctioning. | (Replace E.C.C.S. control unit.) |
| 32 | E.G.R. function | e E.G.R. control valve does not operate. | e E.G.R. control valve |
| (E.G.R. control valve spring does not lift.) | e E.G.R. and canister control | ||
| solenoid valve | |||
| 33 | Exhaust gas sensor cir- | |@ The exhaust gas sensor circuit is open or | e Harness and connector |
| cuit | shorted. | e@ Exhaust gas sensor | |
| (An abnormally high or low output voltage is | e Fuel pressure | ||
| entered.) | e Injectors | ||
| e Intake air leaks | |||
| 34 | Detonation sensor cir- | |@ The detonation circuit is open or shorted. | e@ Harness and connector |
| cuit | (An abnormally high or low voltage is entered.) | e Detonation sensor | |
| 35 | Exhaust gas tempera- | e The exhaust gas temperature sensor circuit is | e Harness and connector |
| ture sensor circuit | open or shorted. | e Exhaust gas temperature | |
| (An abnormally high or low voltage is entered.) | sensor | ||
| 43 | Throttle sensor circuit | e The throttle sensor circuit is open or shorted. | e Harness and connector |
| (An abnormally high or low voltage is. entered.) | e Throttle sensor | ||
| 45 | Injector leak | e Fuel leaks from injector. | @ Injector |
| 54 | Signal circuit from A/T | |e The A/T communication line is open or shorted. | e@ Harness and connector |
| control unit to E.C.U. | |||
| (A/T only) |
*: Check items causing a malfunction of crank angle sensor circuit first, if both ‘““CRANK ANGLE SENSOR (No. 11)” and “IGN SIGNAL-PRIMARY (No. 21)” are displayed one after the other.
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
The malfunction code is erased from the backup memory on the E.C.U. when the diagnostic mode is changed from Mode II to Mode I. (Refer to ‘‘'HOW TO SWITCH MODES’”’.) @ When the battery terminal is disconnected, the malfunction code will be lost from the backup memory within 24 hours. e Before starting self-diagnosis, do not erase the stored memory before beginning self-diagnosis.
EF & EC-43
Parts & tools for this job For Nissan 240SX
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLSocket setSearch: socket set metric
- BOOKHaynes manualSearch: Haynes manual Nissan 240SX
As an Amazon Associate we earn from qualifying purchases.