Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 45 (Cont’d)

AIT control unit

@ NEUTRAL SW CIRCUIT

SHIFT

INSPECTION START

out oF N/P-RANGE

D) ’ THEN

CHECK OVERALL FUNCTION.

O.K..

INSPECTION END

TOUCH START

1) Turn ignition switch “‘ON”. 2) Perform ‘‘NEUTRAL SW

|L START

|

CIRCUIT” in “FUNCTION

SEF206L TEST” mode with CONSULT. OR wMONITOR xNO FAIL [_] 1) Turn ignition switch ‘‘ON”’. 2) Check neutral switch signal in

START SIGNAL

OFF “DATA MONITOR” mode with

IDLE POSITION

ON

AIR COND SIG

OFF CONSULT.

ON “N” or “P”: ON Except above: OFF OR 1) Make sure that inhibitor [RECORD _| switch circuit functions prop- erly. (Refer to AT section.) SEF385J 2) Disconnect E.C.U. harness connector. a DISCONNECT 3) Shift selector lever to ‘‘P”’ | C/UNIT

NEUTRAL SW

|°| CONNECTOR

| => range. 35 4) Turn ignition switch ‘‘ON”’. 5) Check harness continuity between E.C.U. terminal 5) | and body ground. Continuity should exist. 6) Shift selector lever to ‘‘N”’ range. 7) Check harness continuity MEF725A between E.C.U. termina! 65) DISCONNECT and body ground. pr. > DISCONNECT Continuity should exist.

((_cvunrr “cl CONNECTOR |

€) N.G. ¥ 35 ——

|L_cvunrr [el connector |

N.G.

CHECK INPUT SIGNAL CIRCUIT.

> Check the following. 1) Turn ignition switch “OFF’’. e Harness connectors(9), 1300 A/T CONTROL 2) Disconnect A/T control unit harness Gi) [2] UNIT connector. e@ Harness continuity 3) Check harness continuity between between E.C.U. and A/T ro E.C.U. terminal 68) and terminal @. control unit MEF726A Continuity should exist. If N.G., repair harness or connectors. O.K.

Vv. Check E.C.U. pin terminals for damage or the connection of E.C.U. harness connector.

EF & EC-157

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.