Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Electrical Components Inspection (Cont'd)

CRANK ANGLE SENSOR

€> 4 =

1.

Remove distributor assembly from engine. Disconnect ig-

uk X

nition wires and center cable from distributor. (Crank angle

sensor harness connector should remain connected.) Turn ignition switch “‘ON”’. Nm Rotate slowly by hand.

3. Rotate crank angle sensor shaft slowly by hand and check voltage between terminals @, @ and ground.

TerminalVoltage
@ (180° signal) @ (1° signal)Voltage fluctuates between 5V and OV.
@ (1° signal)

Crank angle Sensor

4. Rotate crank angle sensor shaft slowly by hand and check connector . = voltage between terminals @ and () ground. ialeiss)

Measure with circuit tester set in 100 mV range, AC.

| Tester pointer deflects: O.K. Tester pointer does not deflect: N.G. If N.G., replace crank angle sensor. . [\ |

After this inspection, malfunction code No. 11 might be dis-

lo Mol L played though the crank angle sensor is functioning properly. In this case erase the stored memory. SEF749K _ connect P

AIR FLOW METER

by (}

1.

Fold back air flow meter harness connector rubber as

shown in the figure if the harness connector is connected.

2. Turn ignition switch “ON”’. H+) >

3. Start engine and warm it up sufficiently. TN . Check voltage between terminal @ and ground. 4 C H -

ConditionsVoltage V
Ignition switch ‘“‘ON’’ (Engine stopped.)Approximately 0.2
Idle (Engine is warmed-up sufficiently.)Approximately 1.0 - 1.4

SEF748K Terminal

5. IfN.G., remove air flow meter from air duct. Check hot film for damage or dust. Temperature compensation resistor

~~ Hot film

resistor

SEF593K

ENGINE TEMPERATURE SENSOR

1. Disconnect engine temperature sensor harness connector.

2. Check resistance as shown in the figure. [=\3

Temperature °C (°F)Resistance kQ
20 (68)21-29
50 (122)0.68 - 1.00
80 (176)0.30 - 0.33

SEFS36 If N.G., replace engine temperature sensor.

EF & EC-163

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.