Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 38 (Cont'd)

INSPECTION START

¥ O.K.

CHECK CONTROL FUNCTION.

INSPECTION END

wy 1) Start engine. 2) Check voltage between E.C.U. terminalsG@oD,@10,G0d,@iDand ground. Voltage: Battery voltage GOD -: No. 1 cylinder GOD : No. 3 cylinder G1 : No. 2 cylinder G1D : No. 4 cylinder N.G. SEF974I Vv N.G.

CHECK POWER SUPPLY.

> Check the following. 1) Stop engine. e Harness connectors(fs), e x 2) Disconnect injector harness e ‘“BR’”’ fusible link (alb connector and E.C.U. harness e Harness continuity between connector. battery and injector [2] 3) Check voltage between e Harness continuity between terminal @ and ground. E.C.U. and E.C.C.S. relay CES, Voltage: Battery voltage If N.G., repair harness or con- 4) Disconnect E.C.C.S. relay. nectors. 5) Check harness continuity between E.C.U. terminal@o> MEF355A and terminal @ . Continuity should exist. 4 €) 4 €) 1D O.K. v N.G.

CHECK OUTPUT SIGNAL CIR-

,| Repair harness or connectors. I[

CAUNTT {cl CONNECTOR |

cP | a CUIT. 109 1) Check harness continuity be- tween terminal @ and E.C.U. terminalsG@oD,G1D,G0d,C1>. [Q] (& Continuity should exist. O.K. y MEF708A N.G.

CHECK COMPONENT

,| Replace injector. (Injector). Ae 4 €& Refer to ‘‘Electrical Components inspection’.

(_evrt [eo] connector

]| (See page EF & EC-187.) 101 © 110° 103° 112, O.K. @ _e v Check E.C.U. pin terminals for damage or the connection of E.C.U. harness connector. COD: No. 3 cylinder AOD : No. 1 cylinder CiD: No. 2 cylinder 1D: No. 4 cylinder MEF357A|

EF & EC-151

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.