Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 22 (Cont’d)

INSPECTION START

[[_evunrt_[°[ connector | 4€:

= \ B 38°47 enegnee

CHECK POWER SUPPLY.

O.K. > CHECK GROUND CIRCUIT.

1) Turn ignition switch ‘‘ON”’. 1) Turn ignition switch ‘OFF’. @ © 2) Check voltage between E.C.U. 2) Disconnect E.C.U. harness terminals 68), and ground. connector. Wo) Voltage: Battery voltage 3) Check harness continuity be-

. ri) Rt

NG.

tween E.C.U. terminals ©,

= 3) ,GoD God ,di® and engine SEF182K ground. BI Continuity should exist. ——- aia lf N.G., repair harness or con-

|[_camrt_[o| connector ||

€> nectors. 6+13+107 +108 +116 —— , lox. Check E.C.U. pin terminals for damage or the connection of °__* E.C.U. harness connector. (| v ~ serieak

CHECK HARNESS CONTINUITY

[N.G. Check the following.

BETWEEN E.C.C.S. RELAY AND

e Harness connectors (Fa), E.C.U. e Harness continuity between ne af 1) Turn ignition switch “OFF”. E.C.U. and E.C.C.S. relay HS &> Ts €>

2) Disconnect E.C.U. harness

lf N.G., repair harness or con-

if CANIT {cl CONNECTOR ] 3 connector. nectors. 38°47 3) Disconnect E.C.C.S. relay. 4) Check harness continuity be- tween E.C.U. terminals ; and terminal @) . Sy Continuity should exist. 1D {o.k. MEF679A

CHECK VOLTAGE BETWEEN

N.G. | Check the following. 'D] : = 3

E.C.C.S. RELAY AND GROUND.

"| e “BR” fusible link ae, €:)

1) Check voltage between termi-

e Harness continuity between

nals @ , © and ground. E.C.C.S. relay and battery Voltage: Battery voltage lf N.G., repair harness or con- nectors. O* D_©

CHECK VOLTAGE BETWEEN

N.G. || Check the following. ~

E.C.U. AND GROUND.

"| @ Harness connectors(), @

1) Check voltage between E.C.U.

e ‘‘BR’”’ fusible link

= terminal and ground. e Harness continuity between MEF680A Voltage: Battery voltage E.C.U. and battery If N.G., repair harness or con- O.K.

[[_c~nrt {ol CONNECTOR ]

e nectors. @) 46

> © ( SEF 185K EF & EC-97

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.