Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

DIAGNOSES — Overall System - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › DIAGNOSES — Overall System - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXDIAGNOSES — Overall System - Nissan 240SX 1991-1992 Workshop Manual

DIAGNOSES — Overall System

DIAGNOSES — Overall System

Performance Test Diagnoses

TROUBLE DIAGNOSES FOR ABNORMAL PRESSURE

Whenever abnormal pressure of high and/or low sides of the system is noted, diagnosis must be conducted by using a manifold gauge. The large-line zone on the gauge scale (see illustrations.) shown in the following table refers to the standard (normal) pressure range for the corresponding pressure side (high or low). Since the standard (normal) pressure, however, differs from vehicle to vehicle, refer to the “Ambient Temperature-Pressure Characteristics’ chart. Pressure measurements are effective only when ambient temperature is in the range indicated under the heading “INSPECTION DATA (2) Measurement of compressor’s high and low pressures’”’.

Gauge indicationRefrigerant cycleProbable causeCorrective action
Both high and low-pressuree Pressure is reduced soonExcessive refrigerant chargeReduce refrigerant until spec-
sides are too high.after water is splashed onin refrigeration cycleified pressure is obtained.
condenser.
e@ No air bubbles appear in
sight glass when pressure
is reduced.
Air suction by radiator orInsufficient condenser coolinge Clean condenser.
condenser fan is insufficient.performancee Check and repair radiator
{or condenser fan as neces-
{ @ Condenser fins aresary.
clogged.
@ Improper rotation of radi-
ator fan or condenser fan
AC359Ae@ Low-pressure pipe is notPoor heat exchange in con-Evacuate repeatedly and re-
AC359Acold.densercharge system.
e When compressor is(After compressor operation
stopped high-pressurestops, high pressure de- creases too slowly.)
value quickly drops by ap-creases too slowly.) |
proximately 196 kPa (2 kg/cm’, 28 psi). It then de-|
kg/cm’, 28 psi). It then de-Air in refrigeration cycle
creases gradually thereaf-
ter.
Engine tends to overheat.Engine cooling systems mal-Check and repair each en-
function.gine cooling system.
e Areas near low-pressuree Excessive liquid refrigerantReplace expansion valve.
pipe connection and ser-on low-pressure side
vice valves are consider-e Excessive refrigerant dis-
ably cold compared withcharge flow
areas near expansion valvee@ Expansion valve is opena
outlet or evaporator.little compared with the
e Plates are sometimes cov-specification.
ered with frost.| @ Improper thermal valve
@ Improper thermal valve
installation
@ Improper expansion valve
adjustment

HA-60

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.