Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

HOW TO USE THIS MANUAL - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › HOW TO USE THIS MANUAL - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXHOW TO USE THIS MANUAL - Nissan 240SX 1991-1992 Workshop Manual

HOW TO USE THIS MANUAL

HOW TO USE THIS MANUAL

1. A QUICK REFERENCE INDEX, a black tab (e.g. EG) is provided on the first page. You can quickly find the first page of each section by mating it to the section’s black tab.

2. THE CONTENTS are listed on the first page of each section.

3. THE TITLE is indicated on the upper portion of each page and shows the part or system.

4. THE PAGE NUMBER of each section consists of two letters which designate the particular section and a number (e.g. “BR-5’’).

5. THE LARGE ILLUSTRATIONS are exploded views (See below) and contain tightening torques, lubrication points and other information necessary to perform repairs. The illustrations should be used in reference to service matters only. When ordering parts, refer to the appropriate PARTS CATALOG.

xample

Pad retainer

aa E " . (0) 54-64 (5.5 - 6.5, 40 - 47) (Upper side)

_® Main pin to sliding portion Torque a member Inner shim Copper washer nm 17 - 20 (1.7 - 2.0, 12 - 14) a Pad retainer —_ (Lower side)

Z a Brake hose

Air bleeder

(9) 7-9 (0.7 -0.9, 5.1 - 6.5) Pin bolt Outer shim (0) 22 - 31 (2.2 - 3.2, 16 - 23) Pad Cylinder body Wen Piston seal

Feat Dust sea

Piston &

'<)

(5) | Nm (kg-m, ft-lb)

SBR364A

6. THE SMALL ILLUSTRATIONS show the important steps such as inspection, use of special tools, knacks of work and hidden or tricky steps which are not shown in the previous large illustrations. Assembly, inspection and adjustment procedures for the complicated units such as the automatic transaxle or transmission, etc. are presented in a step-by-step format where necessary.

7. The following SYMBOLS AND ABBREVIATIONS are used: ©)

Tightening torque

M/T :

Manual Transaxle/Transmission

Should be lubricated with grease. A/T : Automatic Transaxle/Transmission Unless otherwise indicated, use Tool : Special Service Tools recommended multi-purpose grease. L.H.D. : Left-Hand Drive Should be lubricated with oil. R.H.D. : Right-Hand Drive

Sealing point

A.T.F. -

Automatic Transmission Fluid

@& Checking point D, : Drive range 1st gear '<) Always replace after every disas- D> : Drive range 2nd gear sembly. Ds -

Drive range 3rd gear

x1)

Apply petroleum jelly.

Du -

Drive range 4th gear

O.D. : Overdrive

Apply A.T.F.

* Select with proper thickness.

2. : 2nd range 2nd gear Ww Adjustment is required. 2, : 2nd range ist gear S.D.S. Service Data and Specifications 1 : 1st range 2nd gear L.H., R.H Left-Hand, Right-Hand 1; : 1st range 1st gear

GI-5

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.